Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLinear Access Control Installation: The Long Beach Owner’s Guide
Linear access control installation in Long Beach typically runs between $450 and $1,400, depending on whether we’re installing a keypad, card reader, telephone entry unit, or a full keypad-plus-receiver retrofit on an existing Linear operator. Most jobs we complete the same day we arrive because we stock Linear-compatible keypads, receivers, and controllers on the truck, not just in a catalog. The way owners usually find us: the keypad stopped responding, the remote stopped working after a power flicker, or the gate opens fine manually but won’t trigger from the house. Here is what I found. Here is what it costs. Here is what I left behind.
We’re an independent Long Beach gate company, not affiliated with Linear. That matters because we’re not obligated to push new equipment. If your existing Linear receiver can be repaired with a replacement board or a re-flash, that’s the first thing we check.
Key takeaways:
- Installed Linear access control pricing starts around $450 for a single keypad swap, up to $1,400 for multi-point entry systems
- We stock Linear-compatible parts on the truck in Long Beach, so most calls are one-visit fixes
- Written price before any work starts, under our Haven Standard Clause 1
- Free second opinion on any written estimate from another Long Beach company
- Call (424) 788-1027. A live person answers, 24/7.
Which Linear Models This Applies To
Linear built its reputation on the old Multi-Code and Delta-3 receivers still bolted to thousands of Long Beach gates, then moved into the MegaCode and ACT series for newer installs. The access control side usually involves one of four pieces: the AP-5 entry keypad, the AM-KP keypad, a Multi-Code 109950 or 4120 receiver, or an ACT-34B remote. If you have a Linear PRO Access controller from a commercial install, we work on those too, but residential driveways in Long Beach rarely need that much logic.
The fastest way to identify what you have: open the operator cover and look for the model label on the control board. The board number matters more than the keypad brand stamped on the outside. A Multi-Code 3089 receiver can be paired with a half dozen different keypad housings, and the only way to know is to read the board, not the faceplate. We photograph that label on every visit, by the way. It goes in your job record.
On the OEM versus aftermarket question for Linear specifically: Linear genuine keypads are fine. So are the quality aftermarket versions from North Shore Commercial or Gatehouse, which use the same MegaCode protocol and hold up about the same in salt air. The failure point on both is usually the membrane, not the electronics. In Long Beach, the membrane lasts about four to six years before UV and ocean humidity make the numbers illegible or the buttons stop rebounding. Aftermarket is fine for the keypad. For the receiver board itself, we prefer OEM because the radio frequency tolerance is tighter and a cheap clone drifts faster.
Signs Your Linear Access Control Installation Is Failing
- Keypad beeps but the gate doesn’t move. The code chip in the keypad is fine; the receiver isn’t hearing it. Usually a antenna wire that corroded at the screw terminal or a receiver board that lost its programming after a power surge. We see this weekly on gates near the Colorado Lagoon corridor, where salt air eats copper terminals faster than inland Long Beach.
- The gate opens randomly, usually at night. A neighbor’s remote on the same frequency, or a receiver set to a common default code. Linear’s older Multi-Code receivers shipped with dip switches all in the “on” position, and half of Long Beach never changed them. We re-program to a unique code and document the new setting.
- Remotes work only within ten feet of the gate. The coaxial antenna lead has pulled loose from the receiver or the antenna itself is shattered from sun exposure. This is a thirty-minute fix with parts we carry.
- The keypad works but buttons need to be pressed twice, hard. Membrane failure. The conductive layer under the keys is cracked. Not worth repairing; swap the keypad. A replacement AP-5 runs about $90, and we install it in under an hour.
- No power at the keypad at all. The low-voltage wire between the keypad and the operator has a break, usually where the conduit enters the ground. Long Beach adobe soil shifts with rain and drought, and shallow conduit pulls apart at the elbow. We trench a new run and leave you a photo of the splice point before we close it up.
BeforeAfterReplacement Cost & What’s Included
In Long Beach, a single keypad replacement with installation runs $450 to $650. A receiver board replacement runs $350 to $550, depending on whether we’re replacing the board only or the board plus antenna. A keypad-plus-receiver retrofit with new wiring runs $800 to $1,400, and we use that number when the existing wire is suspect or the operator is far from the keypad location.
Every quote includes the written price before we start, the part cost broken out from labor, and the 365-Day Done Right Promise on the completed work. If the install isn’t right within a year, we make it right at no additional charge. That’s Clause 3, and it applies to every access control job we complete in Long Beach.
What drives the range: whether we’re reusing existing low-voltage wire or pulling new, whether the operator has a spare receiver slot or needs a piggyback board, and whether we’re matching an existing Linear protocol or updating the whole system to MegaCode. We don’t pad the estimate. The price you sign is the price you pay.
DIY or Call Us?
You can safely check three things before calling: read the model number off the control board, test whether the keypad has power at all, and count how many remotes still work. That information saves us a trip and saves you money because we can stage the right parts on the truck.
What we don’t recommend doing yourself: opening the operator housing and probing terminals with the power on. Linear operators carry 120V on the line side, and the low-voltage side is tight quarters. A slipped probe can fry the board, which turns a $500 repair into a $1,200 repair. The same goes for splicing buried low-voltage wire. If the break is underground, the fix is a new conduit run, not electrical tape and hope.
If you’re in Long Beach and want a written price before anyone touches the gate, call (424) 788-1027. We’ll tell you what we think it is over the phone, confirm it in writing on site, and leave you a photo record of everything we touched.
FAQs
Plan on four to six years for the keypad membrane in Long Beach’s salt air and UV exposure, and ten to fifteen years for the receiver board if it’s protected inside the operator housing. Coastal properties near the water see the shorter end of that range. If your keypad is older than six years and acting up, replacement is usually cheaper than repeated service calls. Call (424) 788-1027 and we’ll tell you over the phone what we think you need.
We can repair receiver boards and antenna connections, but keypad membranes are not worth repairing; the part is cheap and the labor to rebuild one exceeds the cost of a new AP-5. We’ll tell you that plainly before we sell you anything. If the board is repairable, we repair it and document the fix.
A single keypad swap takes under an hour. A receiver board replacement takes forty-five minutes to an hour and a half. A full keypad-plus-receiver retrofit with new underground wire takes three to five hours, depending on the conduit run. Most jobs are one visit, same day.
Yes. We carry Linear-compatible AP-5 keypads, Multi-Code receiver boards, antennas, and remotes on the truck in Long Beach. We also stock parts for LiftMaster, Mighty Mule, and Ghost Controls operators, so if your gate has a mixed-brand setup we can usually handle the whole job in one trip. If a part is not on the truck, we tell you that before we schedule, not after we arrive.
Call for a Written Quote
If you’re in Long Beach and your Linear gate stopped answering the keypad, call (424) 788-1027. Adrian Vance and the crew at Vance Gate Repair Long Beach will give you a straight answer on cost, a written price before any work starts, and a photographed record of what we found, what we set, and what we installed. A live person answers, any hour, every day.
Written by Adrian Vance, Owner, Vance Gate Repair Long Beach at Vance Gate Repair Long Beach, serving Long Beach and nearby areas.