Ghost Controls Gate Parts & Welding Nationwide

Ghost Controls Gate Parts & Welding in Long Beach: What to Know First

If you own a Ghost Controls gate opener in Long Beach, you can get independent parts and welding repair without replacing the motor. We repair Ghost Controls hinges, posts, rails, latches, and rollers, and we weld cracked steel on the same visit for most jobs. Prices run from $165 for a gate roller pair to $850 for a full post replacement with concrete work, and every job gets a written price before we touch anything. Call (424) 788-1027 and you’ll talk to a person who can tell you what the repair will cost.

Call (424) 788-1027

This page is for Long Beach homeowners whose Ghost Controls opener still works fine but whose gate hardware has gone bad: sagging hinges, a post that’s pulling out of the concrete, a weld that cracked at the seam, a latch that won’t catch. Those are mechanical problems, not motor problems, and they’re usually fixable in one visit. If you’re not sure whether it’s a parts-and-welding job or a motor issue, call us anyway. We’ll tell you over the phone what we think it is, and we’ll confirm it in writing before you pay anything.

How Ghost Controls Products Fail - and How We Fix Them

• Hinge pin wear on the Ghost Controls swing arm kits. The Ghost Controls swing gate opener mounts to a gate post with a hinge bracket and arm. After three or four years of Long Beach salt air, the hinge pin on that bracket wears into an oval and the gate starts to sag. We see this a lot in neighborhoods near the water. The opener isn’t failing; the hardware is worn. We replace the hinge pin, ream the bracket hole back to round, and set the gate level again.
• Post flex on the Ghost Controls dual gate systems. Ghost Controls dual swing gate openers put constant lateral load on both gate posts every time the gate opens. If the posts weren’t set in deep concrete when the gate was installed, that load cracks the post base or loosens the anchor bolts. We weld a post reinforcement plate or sister a second post alongside, then re-set the base. The gate sits still under load again.
• Broken weld at the gate-to-operator bracket. The Ghost Controls operator arm bolts to a bracket that’s welded to the gate frame. On welded steel gates, that bracket weld is the weak point. When it cracks, the gate jerks at the start of travel and the opener’s limit switch reads it as a fault. We cut out the old weld, grind the joint clean, and lay a full-penetration weld that holds the bracket solid. The opener stops faulting.
• Rail and roller failure on sliding gates with Ghost Controls sliding operators. Ghost Controls makes slide gate openers that ride on a rail with rollers. When the rollers corrode, the gate drags and the motor strains at the end of travel. Long Beach’s marine layer accelerates roller corrosion. We swap the rollers and realign the rail so the gate moves with two fingers of force.
• Latch misalignment on the Ghost Controls magnetic lock models. Ghost Controls sells magnetic lock kits that hold the gate closed when the opener is idle. If the gate drifts out of alignment, the maglock’s strike plate misses and the gate won’t lock. We weld the strike plate in the correct position or refit the latch so the lock engages every time.

Our Ghost Controls Gate Parts & Welding Process

1. 1
   Call and describe the problem. You tell us what the gate does - “it drags at the end,” “the post is leaning” - and we give you a ballpark price over the phone. Written estimate follows before any work starts.
2. 2
   We show up and inspect. Named technician, uniform, photo record of the gate before we touch it. We take measurements, check the Ghost Controls opener for error codes, and write down what we found.
3. 3
   Parts decision. We use OEM Ghost Controls parts when the part is under warranty or the manufacturer tolerances matter. For weld-on brackets and hinges, we use quality aftermarket steel that welds better than the original.
4. 4
   Repair or weld. We do the hinge replacement, post re-setting, rail alignment, or welding on site. Most jobs finish in one visit.
5. 5
   Test and document. The gate runs through a full open-close cycle with the opener connected. We photograph the finished work and the readout from the Ghost Controls control board.
6. 6
   Clean up and hand over the record. You get a photo log of everything we touched and a written receipt with the part numbers. 365-Day Done Right Promise covers it all.

Before

After

What Ghost Controls Gate Parts & Welding Costs in Long Beach

Here’s what we charge for common Ghost Controls hardware jobs in Long Beach. These are the prices you’ll see on a written estimate before work begins, not after:

• Gate roller pair (slide gates): $165-$240, including adjustment of the Ghost Controls slide rail
• Hinge replacement (single gate): $220-$380, depending on hinge size and whether the post needs re-shimming
• Latch and lock repair or replacement: $145-$310, including welding of the strike plate if needed
• Post replacement with concrete work: $650-$850 for a standard 4×4 or 6×6 steel post, including demolition and new concrete
• Custom bracket welding: $180-$420, depending on the bracket size and access
• Rail repair or realignment: $260-$520, including new rollers if the old ones are corroded

What moves the price: how deep the post was set originally, whether the gate is steel or wood, and how far we have to go to reach the job. Long Beach gate post work near the water often costs more because the old post comes out in pieces when the base has rusted through. Call (424) 788-1027 for an exact written quote on your Ghost Controls system. The estimate is free.

Why Long Beach Homeowners Call Vance Gate Repair Long Beach for Ghost Controls Work

We’re an independent Ghost Controls service provider, not a factory warranty center. That means we tell you the truth about what’s worth fixing and what isn’t, even when the truth is that a $40 hinge is all you need. Every technician who walks onto a Long Beach property knows Ghost Controls systems and the other brands too - LiftMaster, Mighty Mule, DoorKing - so if your opener ever does need motor work, you don’t have to find a second company. The written price before work starts is not a courtesy. It’s the rule. The 365-Day Done Right Promise means if our weld or our hinge replacement fails inside a year, we come back and fix it at no charge. Adrian Vance built the company on documenting everything: the photo record, the part number, the before and after. “Here is what I found. Here is what it costs. Here is what I left behind.”

FAQs

Get a Written Price for Your Ghost Controls Gate Repair in Long Beach

If your Ghost Controls opener works but your gate sags, drags, or won’t lock, call Vance Gate Repair Long Beach at (424) 788-1027. We’ll send a technician who knows Ghost Controls hardware, writes down what they find, and gives you a flat price before any work begins. Free estimates, documented photo records, and a real person on the phone at any hour.

Written by Adrian Vance, Owner, Vance Gate Repair Long Beach at Vance Gate Repair Long Beach, serving Long Beach and nearby areas.