Ghost Controls Keypad & Intercom Repair Nationwide

Ghost Controls Keypad & Intercom Repair: The Long Beach Owner’s Guide

Ghost Controls keypad and intercom repair in Long Beach typically runs $165-$385 installed, depending on whether we’re replacing the keypad face, the intercom board, or the full unit, and most jobs are completed the same visit. The way homeowners usually discover the part has failed is unremarkable at first: the gate works fine from the remote but the keypad sits dead, or the intercom crackles and you can’t hear anyone on the other end. Then it stops responding entirely, and you’re left punching in a code that goes nowhere.

Call (424) 788-1027

We stock Ghost Controls-compatible keypads and intercom modules on the truck, which means in most Long Beach cases we can diagnose the failure, match the replacement to your existing system, and have it wired and tested before we hand you the written record of what was installed. We’re an independent service provider, not affiliated with Ghost Controls, and that matters because we’re not steering you toward a full system replacement when the fix is a $200 part swap.

Which Ghost Controls Models This Applies To

The Ghost Controls lineup splits roughly into two compatibility camps, and getting this wrong is the single most avoidable mistake we see on service calls across Long Beach. The original AXDP and HYDP series keypads use a 4-wire connection and a fixed code protocol that will not communicate with the newer AXXP and HDP series boards, which run on a rolling-code signal. If you bought a keypad online and it simply refused to pair, there’s about an even chance the seller listed it as “universal” when it was nothing of the sort.

Ghost Controls keypads live outside the gate and take the brunt of direct sun, coastal fog, and the salt air that moves through Long Beach from the harbor. The keypads are rated for outdoor use, but the membrane buttons on the older generation degrade faster than the board behind them. What we typically replace is the entire keypad housing with a fresh OEM unit, because Ghost Controls does not sell the membrane separately. The intercom modules on Ghost Controls systems are the other common failure point, particularly the call button and the speaker, which corrode at the wiring terminals if the weather seal has stiffened or cracked. When we replace an intercom, we photograph the old wiring before anything is disconnected, wire the new unit to match, and leave you with that record so the next technician, if there ever is one, isn’t guessing.

Signs Your Ghost Controls Keypad or Intercom Is Failing

• Dead keypad with no backlight or beep. This usually points to a power or ground fault at the keypad, not a dead board. We check the wire run before recommending any part replacement.
• Keypad lights up but won’t accept the code. A single stuck or unresponsive button can scramble your entry. This is a membrane failure, and the fix is a new keypad housing because the button layer isn’t sold separately.
• Intercom audio cuts in and out or hums. Corrosion at the speaker terminals or a failing capacitor on the intercom board is the typical culprit. Near the Colorado Lagoon corridor, we see this corrosion pattern more than anywhere else in Long Beach.
• Visitor can hear you, but you can’t hear them, or vice versa. One-directional audio is almost always a bad microphone or speaker on the intercom unit itself. The board may be fine, but the part is cheap enough that replacing the entire intercom module is usually the honest call.
• Gate opens on its own or won’t close after a call button press. This can be a wiring fault or a stuck relay on the intercom board. Left alone, it gets worse and eventually burns out the relay entirely.

Before

After

Replacement Cost & What’s Included

We write the price before any work starts, per Clause 1 of The Haven Standard. For a Ghost Controls keypad replacement in Long Beach, you’re typically looking at $165-$235 installed, including the part, the labor, and the written record of what was installed. Ghost Controls intercom module replacement runs $280-$385 installed, depending on which generation of intercom your system uses and whether the wiring at the junction needs to be re-terminated.

Here is what I found. Here is what it costs. Here is what I left behind. That’s the structure of every invoice we write, and it’s why the price on the page matches the price on the bill. The range accounts for the part itself, the wiring check, and the programming time to sync the new unit to your existing Ghost Controls board. If the wire run from the keypad to the control board is fried, that’s additional material, but we’ll tell you the number before we touch it and you approve it in writing.

Every Ghost Controls keypad or intercom repair we complete is covered under our 365-Day Done Right Promise. If it’s not right within a year, we make it right at no additional charge. No argument, no fee, no expiration date within that window.

DIY or Call Us?

Ghost Controls keypads run on low voltage, and the honest truth is that a handy homeowner can swap one out in about an hour. The part is not inherently dangerous to handle the way a gate spring or high-tension cable is. What goes wrong in DIY work, and what we get called out to fix afterward, is usually the compatibility mismatch: the new keypad doesn’t talk to the board, the wiring was landed in the wrong order, or the weather seal wasn’t seated and the unit is already corroding six months later.

If you want to check something before calling, look at the label on the back of your existing keypad or the board itself. The series letter code tells us most of what we need to know. If you can’t find the label or you’ve already bought a part that won’t pair, that’s exactly the situation we resolve every week. Call (424) 788-1027 and we’ll match the right part to your Ghost Controls system, install it, and hand you the written price and the photo record before we leave the driveway.

FAQs